Gorgeous Group Limited

Gorgeous Group Limited

Specializing in supplying commercial led lighting products

Search Menu
You are here: Home / Archives for led driver / Dimmable led driver / 0-10V

0-10V

0/1-10v Push Dimming LED Driver

0/1-10v & Push Dimming LED Driver, two chanels of dimmable Constant Current LED power supply.

0/1-10v & Push Dimming LED Driver
0/1-10v & Push Dimming LED Driver

 

  1. General Information
    • LED Driver identification HYL-T200-1/12/103E
    • LED control gear type Buit-in
    • LED configuration 200 mA single channel
    • Type of LED’s 200 mA LED or LED module
    • Type of protection IP20
    • Suit for Luminaires Class I

 

  1. Input (Mains) Specifications
    • Nominal voltage 220…240 VAC
    • Nominal frequency 50/60 Hz
    • AC voltage for starting 190 VAC start-up with operating temperature
    • AC operation on 198…264 VAC
    • DC voltage for starting /
    • DC operation on /
    • Surge current /
    • Rated input power ≤14.5 W, @230 VAC
    • Input current <0.065 A, @230 VAC
    • Power factor >0.9, @230 VAC
    • Input current harmonics IEC 61000-3-2
    • Total harmonic distortion ≤20 %
    • Full-load efficiency ≥84 % (typical 86 %)
    • No load power consumption ≤2.0 W
    • Leakage current /
    • Number of mains fuses 1

 

  1. Output (Mains) Specifications
    • Number of channels 1
    • Rated output power ≤12 W, @230 VAC
    • output voltage 3 VDC
    • output voltage 60 VDC
    • declared output voltage 72 VDC
    • Average nominal output current 20/200 mA
    • Output current tolerance (max) ±5 %
    • Dimming
    • Way of dimming
    • Dimming range 20 %/100 %
    • Open circuit proof Yes
    • Overload protection Yes
    • Short circuit protection Yes
    • cable length without LED module ≤1 m
    • ripple current /
    • Type of output Constant Current
    • Overvoltage output protection /
    • Number of output channels 1
    • Turn-on Time ≤0.5 s

  1. Temperatures and Life expectation
    • allowed ambient Temp. -20 ℃
    • allowed ambient Temp. +50 ℃
    • Allowed operating humidity range 5 %…90 %
    • allowed TC Temp. 75 ℃
    • Over temperature protection /
    • life time Up to 50,000hours(25℃, 10% failure rate)
    • switching cycles during life time Up to 10,000 cycles(25℃)

 

  1. Immunity
    • Immunity against static discharge IEC 61547
    • Immunity against radio frequency electric and IEC 61547

Magnetic fields

  • Immunity against power frequency electric and IEC 61547

magnetic fields

  • Immunity against transient voltage fluctuation IEC 61547
  • Immunity against injected currents on AC line IEC 61547
  • Immunity against surge voltage and currents (AC) IEC 61547
  • Immunity against voltage dips (AC) IEC 61547
  • Immunity against voltage interruptions IEC 61547
  • Magnetic shielding

 

  1. RFI Requirements
    • Disturbance voltages at mains terminals according EN 55015

to luminaries of class II (or I)

  • Radiated disturbance voltages EN55015

 

  1. Safety Requirements
    • Cree page distance and clearances IEC 61347-2-13
    • Protection against contact with live parts IEC 61347-2-13
    • Voltage at ballast terminal after 1 min IEC 61347-2-13
    • working voltage IEC 61347-2-13
    • Humidity / insulation resistance test IEC 61347-2-13
    • Humidity / high voltage test IEC 61347-2-13
    • Strength against mechanical damage /

 

  1. Installation and Wiring
    • Terminals Push type
    • Number of mains terminals 1 with 4 ports
    • Number of LED terminals 1 with 2 ports
    • diameter of test contacts 1.2 mm
    • Cross section of wires (any lead) 5…1.5 mm2 massive leads
    • allowed cable capacitance 150 pF
    • allowed cable length 1.5 m
    • distance between LED drivers 5 cm

 

  1. LED Driver Case
    • Case material and identification PC plastis, L103D/E
    • Case drawing Number refer to the attached drawing
    • dimension L103×W67×H25 mm
    • Mounting hole distance 8×W57.5 mm
    • Mounting screws M4
    • Ground connection via /
    • Terminal covers Yes
    • Class of protection IP20
    • Labelling /
    • Barcode identification /

 

  1. Environmental Requirements
    • Noise produced by driver during start /
    • Noise produced by driver during operation <30 dB at distance 1 m
    • Labelling of plastic case Silkscreen
    • Absence of dangerous materials Yes
    • After end of life to be treated as /

 

  1. Approvals
    • Approval according to CQC、CE、CB、SAA、ROHS、EMC、SABS、MEMKO
    • EMV approval according to EN 55015

 

  1. Packaging and Transport
    • Immunity against vibration and shock /
    • Weight (g) /
    • Packing unit 48 pcs/carton /
    • Labelling of package according to 3AAA standards
    • Barcode identification of package according to 3AAA standards

 

  1. Dimension, Drawing Diagram and Label
    • Dimension

 

Click to download HYL-T200-1 12 103E

1-10v Push Dimming LED Driver

1-10v & Push Dimming LED Driver, 3~40W constant current dimmable LED power supply work with 1-10V dimmer (electronic potentiometer)

Main feautures:

  • Dimming way: 1-10V & Push Button Light Dimming
  • Work with 1-10V dimmer (electronic potentiometer)
  • Dimming smooth, no flicking
  • Fixed output constant current LED Driver
  • Synchronization up to 50pcs drivers.
  • 3-40W completed power with different current customized
    (200/260/350/500/700/900 mA)
  • Push dimming is available
  • Can be either used build-in or independent with cable clamp (see accessory)
  • Multiple protection function.
  • Meet the IEC safety regulations & EMC regulations
  • Push wire terminal for quick connection.

Protection:

  • Over temperature protection
  • Over load protection
  • Short-circuit protection
  • No-Load protection

Technical data:

  • Rate Input Voltage 220-240VAC
  • Input Frequency 50/60Hz
  • THD (at 230V, 50Hz, full load) <20%
  • Output Current tolerance ±5%
  • Over load protection
  • Hiccup mode recovers automatically
  • Short circuit protection
  • Over Voltage Protection 320V AC, 1h
  • Over Voltage Protection
  • Latch mode
  • Over temperature protection <130℃
  • Max. output voltage (no-load voltage)60V
  • Turn on time(at 230V, 50Hz, full load)≤0.5s
  • Turn off time(at 230V, 50Hz, full load)≤0.2s
  • Life time >50000h
  • Dimming mode 1-10V & Push Dimming
1-10V & Push Dimming LED Driver
1-10V & Push Dimming LED Driver & power supply

Download data sheet of 1-10v & Push Dimming LED Driver

0-10V dimming led driver 30W IP67

0-10V dimming led driver 30W IP67

LED driver is a device that manages power and controls the current flow for an LED lighting product. The led driver is very important to led lights. According to the different methods of control, it can be divided into dimmable led driver and non-dimmable led driver.We specializing in manufacturing led drivers for many years. We supply triac dimmable led driver/dali dimmable led driver/0-10V dimming led driver and non-dimmable led driver.

0 – 10v dimming led driver is to solve the led lamps and traditional fluorescent lamps cannot be used at the same time.The product can be a very good support 0/1-10V dimmer, and compatible with all major brands lighting dimming system,Well compatible with branded dimmers such as: LUTRON,Clipsal,Philips,Osram etc.

Power supply design with a control chip, 0 to 10v dimmer, by 0-10v voltage change, change the power supply output current, light reduction. For example: when the 0 to 10v dimmer modulation to 0v, the current drop to zero, the lamp brightness is closed, when the 0 to 10v dimmer up 10v, the largest output current also will reach 100% of the output power, brightness will be 100% (the output voltage is the same).

30W IP 67 waterproof 0-10V dimming led driver, Aluminum housing,AC100-265V input voltage, DC 12V output voltage, 0-2.5A output current, PFC>0.9, nice performance, suitable for led downlight, panel light, led ceiling light and so on.

Product parameters:
The input voltage: AC100-265V
Output voltage: DC12V/24V/36V/48V
Wattage:45W
Constant current : 0-2.5A/ 0-1.25A / 0-0.83A/ 0-0.63A
The dimming interface: DC 0 to 10V analog dimming signal
Dimension: the L257*W29*H20mm
PFC:>0.9
IP67 waterproof , Aluminum housing

Model: DV-12030-A-DIM / DV-24045-A-DIM /DV-36045-A-DIM / DV-48045-A-DIM

Packing information: the product size is 257*29*20mm, the net weight is 0.32kg per unit, 50pcs per carton, the Gross weight is 17kg, and the carton size is 324*258*188.

DV-12030-A-DIM

ModelWatts.Input voltageOutput voltageOutput currentSize(mm)PFCN.W/Unit   
DV-12030-A-DIM30WAC100-265VDC 12V0-2.5A257*29*20>0.90.32kg
DV-24030-A-DIM30WAC100-265VDC 24V0-1.25A257*29*20>0.90.32kg
DV-36030-A-DIM30WAC100-265VDC 36V0-0.83A257*29*20>0.90.32kg
DV-48030-A-DIM30WAC100-265VDC 48V0-0.63A257*29*20>0.90.32kg
DV-12036-A-DIM36WAC100-265VDC 12V0-3A257*29*20>0.90.32kg
DV-24036-A-DIM36WAC100-265VDC 24V0-1.5A257*29*20>0.90.32kg
DV-36036-A-DIM36WAC100-265VDC 36V0-1A257*29*20>0.90.32kg
DV-48036-A-DIM36WAC100-265VDC 48V0-0.75A257*29*20>0.90.32kg
DV-12060-A-DIM60WAC100-265VDC 12V0-5A200*70*46
>0.951.1kg
DV-24060-A-DIM60WAC100-265VDC 24V0-2.5A200*70*46
>0.951.1kg
DV-36060-A-DIM60WAC100-265VDC 36V0-1.66A200*70*46
>0.951.1kg
DV-48060-A-DIM60WAC100-265VDC 48V0-1.25A200*70*46
>0.951.1kg
DV-12080-A-DIM80WAC100-265VDC 12V0-6.6A200*70*46
>0.951.1kg
DV-24080-A-DIM80WAC100-265VDC 24V0-3.3A200*70*46
>0.951.1kg
DV-36080-A-DIM80WAC100-265VDC 36V0-2.2A200*70*46
>0.951.1kg
DV-48080-A-DIM80WAC100-265VDC 48V0-1.66A200*70*46
>0.951.1kg
DV-12100-A-DIM100WAC100-265VDC 12V0-8.3A230*70*46>0.981.3kg
DV-24100-A-DIM100WAC100-265VDC 24V0-4.15A230*70*46>0.981.3kg
DV-36100-A-DIM100WAC100-265VDC 36V0-2.8A230*70*46>0.981.3kg
DV-48100-A-DIM100WAC100-265VDC 48V0-2.1A230*70*46>0.981.3kg
DV-12120-A-DIM120WAC100-265VDC 12V0-10A230*70*46>0.981.8kg
DV-24120-A-DIM120WAC100-265VDC 24V0-5A230*70*46>0.981.8kg
DV-36120-A-DIM120WAC100-265VDC 36V0-3.3A230*70*46>0.981.8kg
DV-48120-A-DIM120WAC100-265VDC 48V0-2.5A230*70*46>0.981.8kg
DV-12150-A-DIM150WAC100-265VDC 12V0-12.5A250*80*53>0.981.8kg
DV-24150-A-DIM150WAC100-265VDC 24V0-6.25A250*80*53>0.981.8kg
DV-36150-A-DIM150WAC100-265VDC 36V0-4.16A250*80*53>0.981.8kg
DV-48150-A-DIM150WAC100-265VDC 48V0-3.1A250*80*53>0.981.8kg
DV-12180-A-DIM180WAC100-265VDC 12V0-15A250*80*53>0.981.8kg
DV-24200-A-DIM200WAC100-265VDC 24V0-8.3A250*80*53>0.981.8kg
DV-36180-A-DIM180WAC100-265VDC 36V0-5.6A250*80*53>0.981.8kg
DV-48200-A-DIM200WAC100-265VDC 48V0-4.16A250*80*53>0.981.8kg

Features:

Universal AC input / Full range (up to 265VAC)
Built-in active PFC function
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
Dimming function:0-10V/ 1-10V/ 10VPWM signal or resistance .
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
3 years warranty
High efficiency up to 90%

Environmental conditions:
* working temperature range: 30 ° ~ 60 ° C;
* storage temperature range: 40 ° ~ + 85 ° C;
* humidity (condensate) : 5% ~ 95% RH.
* product cooling method: natural cooling;
* resistance to vibration: 5 ~ 30 minutes; 55 hz / 2 g
* impact resistance: 1 g/S;
* MTBF: 30000 hours, under the condition of full load and 25 ° C temperature;

Note:
1. in the power supply device, please note to the input, output, Ann, correctly, to electricity when confirmed.
2. please pick a good DC output side load, and confirmed to open the power supply; If electricity open, please shut off the power supply, after must wait for output v electricity stored after the release, then the LED, otherwise may burn out the LED;
3. please pay attention to safety, when using electric shock prevention measures, and metal case short circuit must be avoided during installation.

Application:
used in indoor lighting, silicon controlled dimmer mode, the dimming range of 5%-100%, dimming flicker-free, constant current can be used to drive canister light, shoot the light, ceiling lamp, led downlights,panel light, etc., constant pressure drive article lamp, can use day MR16 lamp, etc. Dimming led driver is widely used in ceiling lamp, panel light, lamp, canister light lamps and lanterns.

led ceiling light application led down light application

0-10V dimming led driver 45W

0-10V dimming led driver 45W

LED driver is a device that manages power and controls the current flow for an LED lighting product. The led driver is very important to led lights. According to the different methods of control, it can be divided into dimmable led driver and non-dimmable led driver.We specializing in manufacturing led drivers for many years. We supply triac dimmable led driver/dali dimmable led driver/0-10V dimming led driver and non-dimmable led driver.

0 – 10v dimming led driver is to solve the led lamps and traditional fluorescent lamps cannot be used at the same time.The product can be a very good support 0/1-10V dimmer, and compatible with all major brands lighting dimming system,Well compatible with branded dimmers such as: LUTRON,Clipsal,Philips,Osram etc.

Power supply design with a control chip, 0 to 10v dimmer, by 0-10v voltage change, change the power supply output current, light reduction. For example: when the 0 to 10v dimmer modulation to 0v, the current drop to zero, the lamp brightness is closed, when the 0 to 10v dimmer up 10v, the largest output current also will reach 100% of the output power, brightness will be 100% (the output voltage is the same).

Product parameters:
The input voltage: AC100-265V
Output voltage: DC12V/24V/36V/48V
Wattage:45W
Constant current : 0-3.75A/ 0-1.87A / 0-1.87A/ 0-1.87A
The dimming interface: DC 0 to 10V analog dimming signal
Dimension: the L180 * H60 * W35
PFC:>0.95

Model: DV-12045-P-DIM / DV-24045-P-DIM /DV-36045-P-DIM / DV-48045-P-DIM

DV-12045-P-DIM

ModelWatts.Input voltageOutput voltageOutput currentSize(mm)N.W/UnitQ'ty/Ctn
DV-12020-P-DIM20WAC 100-265VDC 12V0-1.66A140*45*270.19kg50pcs
DV-24020-P-DIM20WAC 100-265V DC 24V0-0.83A140*45*270.19kg50pcs
DV-36020-P-DIM20WAC 100-265V DC 36V0-0.56A140*45*270.19kg50pcs
DV-48020-P-DIM20WAC 100-265V DC 48V0-0.42A140*45*270.19kg50pcs
DV-12030-P-DIM30WAC 100-265VDC 12V0-2.5A180*60*350.55kg20pcs
DV-24030-P-DIM30WAC 100-265V DC 24V0-1.25A180*60*350.55kg20pcs
DV-36030-P-DIM30WAC 100-265V DC 36V0-0.83A180*60*350.55kg20pcs
DV-48030-P-DIM30WAC 100-265V DC 48V0-0.63A180*60*350.55kg20pcs
DV-12036-P-DIM36WAC 100-265VDC 12V0-3A180*60*350.55kg20pcs
DV-24036-P-DIM36WAC 100-265V DC 24V0-1.5A180*60*350.55kg20pcs
DV-36036-P-DIM36WAC 100-265V DC 36V0-1A180*60*350.55kg20pcs
DV-48036-P-DIM36WAC 100-265V DC 48V0-0.75A180*60*350.55kg20pcs
DV-12045-P-DIM45WAC 100-265VDC 12V0-3.75A180*60*350.55kg20pcs
DV-24045-P-DIM45WAC 100-265V DC 24V0-1.87A180*60*350.55kg20pcs
DV-36045-P-DIM45WAC 100-265V DC 36V0-1.87A180*60*350.55kg20pcs
DV-48045-P-DIM45WAC 100-265V DC 48V0-1.87A180*60*350.55kg20pcs

Features:

Universal AC input / Full range (up to 265VAC)
Built-in active PFC function
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
Dimming function:0-10V/ 1-10V/ 10VPWM signal or resistance .
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
3 years warranty
High efficiency up to 90%

Environmental conditions:
* working temperature range: 30 ° ~ 60 ° C;
* storage temperature range: 40 ° ~ + 85 ° C;
* humidity (condensate) : 5% ~ 95% RH.
* product cooling method: natural cooling;
* resistance to vibration: 5 ~ 30 minutes; 55 hz / 2 g
* impact resistance: 1 g/S;
* MTBF: 30000 hours, under the condition of full load and 25 ° C temperature;

Note:
1. in the power supply device, please note to the input, output, Ann, correctly, to electricity when confirmed.
2. please pick a good DC output side load, and confirmed to open the power supply; If electricity open, please shut off the power supply, after must wait for output v electricity stored after the release, then the LED, otherwise may burn out the LED;
3. please pay attention to safety, when using electric shock prevention measures, and metal case short circuit must be avoided during installation.

Application:
used in indoor lighting, silicon controlled dimmer mode, the dimming range of 5%-100%, dimming flicker-free, constant current can be used to drive canister light, shoot the light, ceiling lamp, led downlights,panel light, etc., constant pressure drive article lamp, can use day MR16 lamp, etc. Dimming led driver is widely used in ceiling lamp, panel light, lamp, canister light lamps and lanterns, such as through the regulator that move light more electricity saving, light and soft!

0-10V dimming led driver 20W

0-10V dimming led driver 20W

LED driver is a device that manages power and controls the current flow for an LED lighting product. The led driver is very important to led lights. According to the different methods of control, it can be divided into dimmable led driver and non-dimmable led driver.We specializing in manufacturing led drivers for many years. We supply triac dimmable led driver/dali dimmable led driver/0-10V dimming led driver and non-dimmable led driver.

0 – 10v dimming led driver is to solve the led lamps and traditional fluorescent lamps cannot be used at the same time.The product can be a very good support 0/1-10V dimmer, and compatible with all major brands lighting dimming system,Well compatible with branded dimmers such as: LUTRON,Clipsal,Philips,Osram etc.

Power supply design with a control chip, 0 to 10v dimmer, by 0-10v voltage change, change the power supply output current, light reduction. For example: when the 0 to 10v dimmer modulation to 0v, the current drop to zero, the lamp brightness is closed, when the 0 to 10v dimmer up 10v, the largest output current also will reach 100% of the output power, brightness will be 100% (the output voltage is the same).

Product parameters:
The input voltage: AC100-265V
Output voltage: DC12V/24V/36V/48V
Wattage:20W
Constant current : 0-1.66A /0-0.83A / 0-0.56A/ 0-0.42A
The dimming interface: DC 0 to 10V analog dimming signal
Dimension: the L140 * H45 * W27
PFC:>0.9

Model: DV-12020-P-DIM / DV-24020-P-DIM / DV-36020-P-DIM / DV-48020-P-DIM

DV-12020-P-DIM

ModelWatts.Input voltageOutput voltageOutput currentSize(mm)N.W/UnitQ'ty/Ctn
DV-12020-P-DIM20WAC 100-265VDC 12V0-1.66A140*45*270.19kg50pcs
DV-24020-P-DIM20WAC 100-265V DC 24V0-0.83A140*45*270.19kg50pcs
DV-36020-P-DIM20WAC 100-265V DC 36V0-0.56A140*45*270.19kg50pcs
DV-48020-P-DIM20WAC 100-265V DC 48V0-0.42A140*45*270.19kg50pcs
DV-12030-P-DIM30WAC 100-265VDC 12V0-2.5A180*60*350.55kg20pcs
DV-24030-P-DIM30WAC 100-265V DC 24V0-1.25A180*60*350.55kg20pcs
DV-36030-P-DIM30WAC 100-265V DC 36V0-0.83A180*60*350.55kg20pcs
DV-48030-P-DIM30WAC 100-265V DC 48V0-0.63A180*60*350.55kg20pcs
DV-12036-P-DIM36WAC 100-265VDC 12V0-3A180*60*350.55kg20pcs
DV-24036-P-DIM36WAC 100-265V DC 24V0-1.5A180*60*350.55kg20pcs
DV-36036-P-DIM36WAC 100-265V DC 36V0-1A180*60*350.55kg20pcs
DV-48036-P-DIM36WAC 100-265V DC 48V0-0.75A180*60*350.55kg20pcs
DV-12045-P-DIM45WAC 100-265VDC 12V0-3.75A180*60*350.55kg20pcs
DV-24045-P-DIM45WAC 100-265V DC 24V0-1.87A180*60*350.55kg20pcs
DV-36045-P-DIM45WAC 100-265V DC 36V0-1.87A180*60*350.55kg20pcs
DV-48045-P-DIM45WAC 100-265V DC 48V0-1.87A180*60*350.55kg20pcs

Features:

Universal AC input / Full range (up to 265VAC)
Built-in active PFC function
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
Dimming function:0-10V/ 1-10V/ 10VPWM signal or resistance .
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
3 years warranty
High efficiency up to 90%

Environmental conditions:
* working temperature range: 30 ° ~ 60 ° C;
* storage temperature range: 40 ° ~ + 85 ° C;
* humidity (condensate) : 5% ~ 95% RH.
* product cooling method: natural cooling;
* resistance to vibration: 5~30 minutes; 55 hz/2 g
* MTBF: 30000 hours, under the condition of full load and 25 ° C temperature;

Note:
1. in the power supply device, please note to the input, output, Ann, correctly, to electricity when confirmed.
2. please pick a good DC output side load, and confirmed to open the power supply; If electricity open, please shut off the power supply, after must wait for output v electricity stored after the release, then the LED, otherwise may burn out the LED;
3. please pay attention to safety, when using electric shock prevention measures, and metal case short circuit must be avoided during installation.

Application:
used in indoor lighting, silicon controlled dimmer mode, the dimming range of 5%-100%, dimming flicker-free, constant current can be used to drive canister light, shoot the light, ceiling lamp, led downlights,panel light, etc., constant pressure drive article lamp, can use day MR16 lamp, etc. Dimming led driver is widely used in ceiling lamp, panel light, lamp, canister light lamps and lanterns, such as through the regulator that move light more electricity saving, light and soft!

0-10V dimming led driver 30W

0-10V dimming led driver 30W

LED driver is a device that manages power and controls the current flow for an LED lighting product. The led driver is very important to led lights. According to the different methods of control, it can be divided into dimmable led driver and non-dimmable led driver.We specializing in manufacturing led drivers for many years. We supply triac dimmable led driver/dali dimmable led driver/0-10V dimming led driver and non-dimmable led driver.

0 – 10v dimming led driver is to solve the led lamps and traditional fluorescent lamps cannot be used at the same time.The product can be a very good support 0/1-10V dimmer, and compatible with all major brands lighting dimming system,Well compatible with branded dimmers such as: LUTRON,Clipsal,Philips,Osram etc.

Power supply design with a control chip, 0 to 10v dimmer, by 0-10v voltage change, change the power supply output current, light reduction. For example: when the 0 to 10v dimmer modulation to 0v, the current drop to zero, the lamp brightness is closed, when the 0 to 10v dimmer up 10v, the largest output current also will reach 100% of the output power, brightness will be 100% (the output voltage is the same).

Product parameters:
The input voltage: AC100-265V
Output voltage: DC12V/24V/36V/48V
Wattage:30W
Constant current : 0-2.5A/ 0-1.25A / 0-0.83A/ 0-0.63A
The dimming interface: DC 0 to 10V analog dimming signal
Dimension: the L180 * H60 * W35
PFC:>0.9

Model: DV-12030-P-DIM / DV-24030-P-DIM /DV-36030-P-DIM / DV-48030-P-DIM

DV-12030-P-DIM

 

ModelWatts.Input voltageOutput voltageOutput currentSize(mm)N.W/UnitQ'ty/Ctn
DV-12020-P-DIM20WAC 100-265VDC 12V0-1.66A140*45*270.19kg50pcs
DV-24020-P-DIM20WAC 100-265V DC 24V0-0.83A140*45*270.19kg50pcs
DV-36020-P-DIM20WAC 100-265V DC 36V0-0.56A140*45*270.19kg50pcs
DV-48020-P-DIM20WAC 100-265V DC 48V0-0.42A140*45*270.19kg50pcs
DV-12030-P-DIM30WAC 100-265VDC 12V0-2.5A180*60*350.55kg20pcs
DV-24030-P-DIM30WAC 100-265V DC 24V0-1.25A180*60*350.55kg20pcs
DV-36030-P-DIM30WAC 100-265V DC 36V0-0.83A180*60*350.55kg20pcs
DV-48030-P-DIM30WAC 100-265V DC 48V0-0.63A180*60*350.55kg20pcs
DV-12036-P-DIM36WAC 100-265VDC 12V0-3A180*60*350.55kg20pcs
DV-24036-P-DIM36WAC 100-265V DC 24V0-1.5A180*60*350.55kg20pcs
DV-36036-P-DIM36WAC 100-265V DC 36V0-1A180*60*350.55kg20pcs
DV-48036-P-DIM36WAC 100-265V DC 48V0-0.75A180*60*350.55kg20pcs
DV-12045-P-DIM45WAC 100-265VDC 12V0-3.75A180*60*350.55kg20pcs
DV-24045-P-DIM45WAC 100-265V DC 24V0-1.87A180*60*350.55kg20pcs
DV-36045-P-DIM45WAC 100-265V DC 36V0-1.87A180*60*350.55kg20pcs
DV-48045-P-DIM45WAC 100-265V DC 48V0-1.87A180*60*350.55kg20pcs

 

Features:

Universal AC input / Full range (up to 265VAC)
Built-in active PFC function
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
Dimming function:0-10V/ 1-10V/ 10VPWM signal or resistance .
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
3 years warranty
High efficiency up to 90%

Environmental conditions:
* working temperature range: 30 ° ~ 60 ° C;
* storage temperature range: 40 ° ~ + 85 ° C;
* humidity (condensate) : 5% ~ 95% RH.
* product cooling method: natural cooling;
* resistance to vibration: 5 ~ 30 minutes; 55 hz / 2 g
* impact resistance: 1 g/S;
* MTBF: 30000 hours, under the condition of full load and 25 ° C temperature;

Note:
1. in the power supply device, please note to the input, output, Ann, correctly, to electricity when confirmed.
2. please pick a good DC output side load, and confirmed to open the power supply; If electricity open, please shut off the power supply, after must wait for output v electricity stored after the release, then the LED, otherwise may burn out the LED;
3. please pay attention to safety, when using electric shock prevention measures, and metal case short circuit must be avoided during installation.

Application:
used in indoor lighting, silicon controlled dimmer mode, the dimming range of 5%-100%, dimming flicker-free, constant current can be used to drive canister light, shoot the light, ceiling lamp, led downlights,panel light, etc., constant pressure drive article lamp, can use day MR16 lamp, etc. Dimming led driver is widely used in ceiling lamp, panel light, lamp, canister light lamps and lanterns, such as through the regulator that move light more electricity saving, light and soft!

Don`t copy text!